|
Your complete package includes:
> free Priority Mail with delivery confirm code.
>Two stereo patch cords to allow use with either a stereo system or computer sound card with line-in.
>Wall adaptor.
from a recent customer........
"Hello, I just wanted to express my appreciation for the excellent service & product!
I placed my order online Monday afternoon and received the Tonar pre-amp yesterday.
After a few hours of listening to vinyl I feel it's an incredible bargain in phono pre-amps.
I spent 3-times as much for a Gram-Slee SE MM-only phono preamp and the Tonar
sounds just as good in the MM setting and it has the capability of MC as well. In
addition to that the Tonar is encased in metal and the Gram Slee is housed in plastic
which leaves it prone to picking up noise, which has been a problem. As a result the
Slee is probably going on Craigslist or eBay or being retired as a back up. I wish all
purchases I make in the future can have as great a pay-off as this one has been.
Thanks guys!"
With outstanding specs and care in workmanship, we are happy to offer this Tonar brand
high end pre-amp for better and best quality systems of all brands. With a signal to noise
ratio far above what any record can produce, you will never outgrow this unit.
Selecting The Cartridge Mode
The Vinyline preamplifier must be used in either the MM (moving magnet) or MC (moving coil)
mode. If you are unsure of your cartridge type, please refer to the information that came with
the cartridge or consult a dealer. The push-button switch on the back of the unit allows you to
select the correct setting for your cartridge. With the switch depressed it is in the MC mode
and with the switch out it is in the MM mode. Please refer to the photo below. Be sure to
disconnect the power supply before changing the mode to prevent possible overload of the signal. Connecting the turntable
Before making any audio connections, please disconnect the power supply.
Connect the turntable’s audio cable to the “ IN” jacks on your Vinyline preamplifier. It is important
that the left and right channel connections are made correctly: the right channel is usually marked
red and the left channel is usually white or black. If there is a grounding wire connected to the
turntable, it should be connected to the “GND” terminal post. Please refer to the photo below.
Connecting to the amplifier
Connect an audio cable from the “OUT” jacks on the Vinyline preamplifier to a line input on your
amplifier (e.g. AUX, Tuner, Tape, CD). (Do NOT use an input marked “Phono” as it will be overloaded
by the already amplified signal). Again, make sure that the left and right channels are correctly connected.
Power Supply Connection
The Vinyline phono preamplifier is supplied with a power supply suitable for your local hydro type
(e.g. 110 or 220v). Check the label on the power supply to be sure you have the correct type for
your area. Before plugging the power adaptor into a wall receptacle, first connect the low voltage
output lead from the power supply to the “16V AC” socket on the back of the Vinyline preamplifier.
(refer to photo on P.1) Do not use any other adaptor except the one supplied.
Common Troubleshooting Tips
•No audio signal on one or both channels:
-Audio RCA plug not fully inserted into the jack of either the Vinyline
preamplifier or the main amplifier.
-Defective cable plug or a break in the cable.
-Power supply for Vinyline not plugged in or Amplifier not turned on.
•Noticeable hum:
-No ground wire connection from the turntable to the Vinyline preamplifier grounding post.
-Possible ground loop problem. Try different grounding scenarios, such as removing the
grounding connection or connecting directly to the main amplifier grounding post.
•Output from the Vinyline preamplifier too loud, too soft, or distorted:
-Incorrect setting of the MM/MC switch. Turn down the amplifier volume control and change
the MM/MC selector switch. Slowly turn up the amplifier volume control to verify that the problem
has been corrected. If you are still experiencing problems, please consult with your dealer
Warranty
Your Vinyline phono preamplifier is warranted against defects for a period of one year from purchase.
Keep your receipt as proof of purchase and return the unit to the selling dealer for warranty handling.
The unit will be repaired or replaced at the discretion of the manufacturer. Modifications or changes
of any type to the product will nullify the warranty and release the manufacturer of any liability.
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use.
Technical Specifications:
Input impedance: MM: 47k Ohm/100pF, MC: 100 Ohm/100pF
Output voltage is: 200mV/1kHz
with MM input of 5.00mV/1kHz
with MC input of 0.45mV/1kHz (aka MC 2.25mVout cartridge produces 1Vpp or 1 volt out)
Gain: MM: 32dB, MC: 53dB
Signal to Noise (Noise floor):
MM: -88dB MC: -79dB
THD: 0.005%
RIAA-equalisation curve accuracy: 20Hz - 20kHz / max. 0.5dB
Power supply: 15V/200mA AC adaptor included
|
