Status: Sept 2020 - We are 100% OPEN. Stay safe and enjoy those recordings at home once again.

TurntableNeedles.com Website logo
Hello Guest! Login
Menu
0 Items / $0
Flat Belt, Super Small 17.2 Inch
Small Flat Drive Belt

Flat Belt, Super Small 17.2 Inch

Our ID#:FBSS17.2
Brand:AVCR
Rubber drive belt (band) for consumer electronics.
$18.00
Oregon USA Stock - 0-24hr Shipping
DiscountPricing
Discount
Pricing
  • 2
  • $14.00
  • 3
  • $13.00
  • 4
  • $12.00
  • 5+
  • $12.00

Reward Points

18 points can be awarded to your webstore account (see FAQ).

17.2 Inch Long Small Flat Electronics Drive Belt


S

17.2" Flat Belt Super Small

May be found in but not necessarily limited to the following:

GARRARD 40-B
GARRARD 86-SB
GARRARD 100C
GARRARD 100S
GARRARD 100SC
GARRARD 125-SB
GARRARD GT-10
GARRARD GT-12
GARRARD GT-15
GARRARD GT-25
GARRARD GT-35/P
GARRARD GT-55
GARRARD GT-120AP
GARRARD GT-250
GARRARD GT-250P
GARRARD GT-250AP
GARRARD GT-350
GARRARD GT-350A
GARRARD GT-350AP
GARRARD ZERO-100-SB
GARRARD SP-25 Mk V
GARRARD SP-35 Mk VI
GARRARD 0-100-SB
GARRARD V-VI
GARRARD X-40B

IMPORTANT: At 0.023" thick, this FBSS17.2 belt is the thinner of two 17.2 models available. You will want to also match the thickness as well as the length and width of your old belt. Then choose this belt if your old belt is closer to 0.023" thick or scroll down to the FBS17.2 belt if your old belt is closer to 0.040" thick and please advise us your make/model. At press time it is the technician's opinion that most original belts will more closely match the FBS17.2 belt below.

  • Meets or exceeds OEM specs. Found in many types of equipment.
  • This belt is of recent manufacture. Original legacy belts no longer exist. If they did, they'd be too old to sell in good conscience. As far as we can tell, even if the manufacturer name was stamped on the belt, all belts supplied with original turntables were outsourced to a belt specialist manufacturer, like ours are today. Our belts are made using state-of-the-art vulcanization chemistry, forming highly crosslinked polymetric structures which ensure long-term elastic stability even under the harshest conditions.
  • Prior to installation of your new belt, the belt path should be cleaned. Here in the repair shop we would use common household rubbing alcohol (isopropyl) or a similar solution to clean the old, (often invisible) belt residue from the entire belt path, including the hub around the underside of the platter, so it doesn't contaminate the new belt. With the belt off, we would get the turntable into play condition and hold an alcohol soaked Q-tip on the side of the spinning belt motor pulley. It's amazing how much black contamination comes off from the old belt. See our belt installation page for related details.

  • 5 Stars
    Turntable Owner
    I have a Yamaha belt drive turntable that is approaching 40 years of age and had not been used for years. This belt rescued my turntable and made it possible for my wife and me to listen to our collection of approximately 1000 LP's. We are grateful that the belt was available.
    Helpful? 
    Reviewed by:  from Orlando, Fl.. on 5/19/2017
    5

    Related Items:

     
     

    Recently Viewed Items

    TurntableNeedles.com logo
    Links
    Categories