3.2 Inch Long Small Square Electronics Rubber Drive Belt

Belt is of recent manufacture. Meets or exceeds OEM specs.
Found in many types of equipment.
This belt is found in but NOT limited to:
• AIWA AD-6700
AIWA AD-6900 Mark II
AIWA ADL-450
AIWA ADM-600H
AIWA ADM-700U BU
AIWA ADM-800
AIWA CT-X15 Sub B
AIWA M-501
AIWA SDL-50
BASF 9200
CALIFONE AV-3500
CALIFONE AV-3510
CALIFONE AV-3600 3500R B 3550 B 4500 B 4700 B 5100R B 5150R B 5300R B 5500R B 5550R B 5900R B 6150R B 6700RT B 6900RT B 6950RT B 7500R 8100R B 8200R A 8300R A 8400RT A 8550R 8600RT B 8625RT B 8725RT B 9300TB 9500TB CH-CS1 B PE-894A-01 B PE-894A-02 B PE-895A-01 B PE-895A-02 B PP-9028 PT-975C B PU-894A-01 B PU-895A-01 B RN-9008 TRX-10 B TRX-100 B
CRAIG 2636
CRAIG J-570 CRAIG J-580 CRAIG T-618 CYBERNET SPC-80 2870 3-5161A F Wind 3-5230A 3-5251 A 3-5443A 3-5445A 3-5446A RP-1838 TD-091 SC-25 CP-10EX CP-90S D-800
LUXMAN K-03 95 3552 3553 3554 3558
ONKYO TA-1500
ONKYO TA-2066
ONKYO TA-2070
ONKYO TA-W80 RQ-208S RS-253S RS-J1 RS-M222 FF RX-5600 1156-8797 5013 CT-3 CT-4 CT-330 CT-F1000 KP-300 KP-310 KP-334 KP-345 14-870K RS-1000 SCM-6550 M-2200 M-2212 M-2213 M-6400 M-G1 M-G2 MG-2 RT-107 RT-350 SC-107U BM-25 A MD TC-142 XR-3320 XR-4420 XR-5620
TECHNICS M-235-X
TECHNICS M-235X
TOSHIBA PC-D15 B KD-9X KD-9XG SCM-6550 RP-101 RP-103 RP-107 RP-117 PS-X555ES (Tonearm)

Meets or exceeds OEM specs. Found in many types of equipment.

This belt is of recent manufacture. Original legacy belts no longer exist. If they did, they'd be too old to sell in good conscience. As far as we can tell, even if the manufacturer name was stamped on the belt, all belts supplied with original turntables were outsourced to a belt specialist manufacturer, like ours are today. Our belts are made using state-of-the-art vulcanization chemistry, forming highly crosslinked polymetric structures which ensure long-term elastic stability even under the harshest conditions.

Prior to installation of your new belt, the belt path should be cleaned. Here in the repair shop we would use common household rubbing alcohol (isopropyl) or a similar solution to clean the old, (often invisible) belt residue from the entire belt path, including the hub around the underside of the platter,so it doesn't contaminate the new belt. With the belt off, we would get the turntable into play condition and hold an alcohol soaked Q-tip on the side of the spinning belt motor pulley. It's amazing how much black contamination comes off from the old belt. See our belt installation page for related details.